manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 50 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 50

Electrical connection

Proline Promag P 500 HART

50

Hauser

7.3  

Connecting the measuring device: Proline 500

NOTICE

Limitation of electrical safety due to incorrect connection!

‣

Have electrical connection work carried out by appropriately trained specialists only.

‣

Observe applicable federal/national installation codes and regulations.

‣

Comply with local workplace safety regulations.

‣

Always connect the protective ground cable  before connecting additional cables.

‣

For use in potentially explosive atmospheres, observe the information in the device-

specific Ex documentation.

7.3.1  

Connecting the connecting cable

L

WARNING

Risk of damaging the electronic components!

‣

Connect the sensor and transmitter to the same potential equalization.

‣

Only connect the sensor to a transmitter with the same serial number.

‣

Ground the connection housing of the sensor via the external screw terminal.

Connecting cable terminal assignment

42 41

GND

E1

S1

E2 S2

S

E

GND

E1 E2

E

ER

+

+

ER

ER

ER

4

5

6

7

8

36 37

42 41

4

5

7

37

n.c.

n.c.

5

3

2

8

1

3

7

4

5

6

n.c.

  A0029145

1

Protective earth (PE)

2

Cable entry for coil current cable on transmitter connection housing

3

Coil current cable

4

Cable entry for signal cable on transmitter connection housing

5

Signal cable

6

Cable entry for signal cable on sensor connection housing

7

Cable entry for coil current cable on sensor connection housing

8

Protective earth (PE)

Connecting the connecting cable to the sensor connection housing

Connection via terminals with order code for "Housing":

Option 

A

 "Aluminum coated"→   51

Connecting the connecting cable to the transmitter

The cable is connected to the transmitter via terminals →   52.

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments