Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 109

Page: 109 / 210

Proline Promag P 500 HART

Commissioning

Hauser

109

Parameter

Prerequisite

Description

Selection / User
interface / User

entry

Factory setting

Switch-off delay

• The

Switch

option is

selected in the

Operating

mode

parameter.

• The

Limit

option is selected

in the

Switch output

function

parameter.

Define delay for the switch-off
of status output.

0.0 to 100.0 s

0.0 s

Failure mode

–

Define output behavior in
alarm condition.

• Actual status
• Open
• Closed

Open

Invert output signal

–

Invert the output signal.

• No
• Yes

Visibility depends on order options or device settings

10.4.8 Configuring the local display

The

Display

wizard guides you systematically through all the parameters that can

configured for configuring the local display.

Navigation

"Setup" menu → Display

‣

Display

Format display

→  110

Value 1 display

→  110

0% bargraph value 1

→  110

100% bargraph value 1

Value 2 display

Value 3 display

0% bargraph value 3

100% bargraph value 3

→  110

Value 4 display

→  110

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Search results

Summary of Contents for Hart Proline Promag P 500

Reviews:

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 109 / 210

Search results

Summary of Contents for Hart Proline Promag P 500

Reviews: