manualshive.com logo in svg

Endress+Hauser Hart Proline Promag P 500, Operating Instructions Manual, Page: 149 / 210

Share
Download
Endress+Hauser Hart Proline Promag P 500 Operating Instructions Manual Download Page 149

Proline Promag P 500 HART

Diagnostics and troubleshooting

Hauser

149

Power

I/O   2

I/O   3

I/O   3

1

2

3

4

5

3.

-

+

-

ESC

2.

Power

open

press

open

press

ESC

E

+

-

I/O  4

Power

I/O  2

I/O  3

1.

  A0029689

1

Supply voltage

2

Device status

3

Not used

4

Communication

5

Service interface (CDI) active

1. Open the housing cover.
2. Remove the display module.
3. Fold open the terminal cover.

LED

Color

Meaning

1

Supply voltage

Off

Supply voltage is off or too low.

Green

Supply voltage is ok.

2

Device status

Off

Firmware error

Green

Device status is ok.

Flashing green

Device is not configured.

Flashing red

A diagnostic event with "Warning" diagnostic
behavior has occurred.

Red

A diagnostic event with "Alarm" diagnostic behavior
has occurred.

Flashing red/green

The device restarts.

3

Not used

–

–

4

Communication

Off

Communication not active.

White

Communication active.

5

Service interface (CDI)

Off

Not connected or no connection established.

Yellow

Connected and connection established.

Flashing yellow

Service interface active.

Proline 500

Different LEDs in the transmitter provide information on the device status.

Summary of Contents for Hart Proline Promag P 500



















































































































































































































Reviews:

No comments