26534-1-0610
Page 22
%851(525,),&(&219(56,216ORSHVW\OHEXUQHUV
8b. On model BVP42FP3 series fireplaces, you will have a
rectangular slope style burner. To gain access to the main
RUL¿FHGLVFRQQHFWWKHJDVVXSSO\WXELQJDWWKHDLUVKXWWHU
E 5HPRYHWKHRUL¿FHKROGHUIURPWKHDLUVKXWWHUWKHQUHPRYH
WKH1*RUL¿FH
E5HSODFH WKH UHPRYHG 1* RUL¿FH ZLWK WKH QHZ /3 RUL¿FH
GHVLJQDWHG LQ WKH RUL¿FH UHIHUHQFH FKDUW IRU \RXU ¿UHSODFH
PRGHO6HFXUHWKHQHZRUL¿FHDQGUHSODFHWKHRUL¿FHRUL¿FH
holder back into the air shutter and secure.
11b.Loosen the air shutter screw and reset the air shutter opening
in accordance with the dimension shown in the reference chart
IRUWKHDSSURSULDWHPRGHO¿UHSODFH
3,/2725,),&(&219(56,21
12. Locate the pilot assembly.
3XOOXSZDUGRQWKHURXQGSLORWÀDPHKRRGWRUHPRYH
H[$OOHQZUHQFKUHPRYHWKHSLORWRUL¿FHWKHQ
UHSODFHZLWKWKHQHZSLORWRUL¿FHPDUNHG
,03257$17)DLOXUHWRLQVWDOOWKHFRUUHFWRUL¿FHZLOOUHVXOW
LQXQLWRYHU¿ULQJWKDWFRXOGRYHUKHDWWKHDSSOLDQFHDQGUHVXOW
LQD¿UH
5HIHU WR ORJ SODFHPHQW IRXQG LQ \RXU ¿UHSODFH LQVWDOODWLRQ
manual to place logs onto the burner assembly.
16. Loosen screw and attach a manometer or pressure gauge to
the outlet pressure tap of the control valve.
17. Turn on the gas supply. Turn on the electrical supply to the
appliance. Check for gas leaks using a soap and water solution
or leak detection solution. Bubbles indicate a leak that MUST
EHFRUUHFWHG'RQRWXVHDQRSHQÀDPHWRWHVWIRUJDVOHDNV
18. Check the air shutter opening. See chart and illustration
below.
19. Relight the main burners and verify proper burner ignition and
operation.
20. With the main burner burning, read the pressure on the
manometer or pressure gauge. The pressure on the gauge
should read between 9.8" and 10.2"w.c.
21. Turn off the gas supply. Turn off the electrical supply to the
appliance.
22. Remove the manometer or pressure gage. Tighten the screw
in the pressure tap.
23. Turn on the gas supply. Turn on the electrical supply to the
appliance.
24. Immediately test all gas line connections and the control valve
for gas leaks using a soap and water solution or gas detection
for solution. Bubbles indicate a leak that MUST be corrected.
'RQRWXVHDQRSHQÀDPHWRFKHFNIRUJDVOHDNV
8VLQJ D EDOO SRLQW SHQ ¿OO RXW WKH FRQYHUVLRQ ODEHO WKDW LV
supplied with the conversion kit. Place the conversion label
adjacent to the rating plate.
7HVWRSHUDWLRQRI¿UHSODFHRQFHDJDLQ$OORZWKH¿UHSODFHWR
RSHUDWHIRUDWOHDVWPLQXWHVDQGFKHFNÀDPHFRORUDWLRQ
Flame on rear of burner should be yellow without any
orange-colored tip. Minor adjustment of the air shutter may
EHQHFHVVDU\WRWXQHLQWKHSURSHUÀDPHFRORU
7KHEXUQHUÀDPHDQGSLORWÀDPHPXVWEHFKHFNHGIRUSURSHU
ÀDPHFKDUDFWHULVWLFVDVRXWOLQHGLQWKLVPDQXDO
9 ( 5 , ) < , 1 * , 1 3 8 7 5 $7 ( 2 ) & 2 1 9 ( 5 7 ( '
FIREPLACE
7KHLQSXWRIWKH¿UHSODFHPXVWEHFKHFNHGDVIROORZV
1.
Turn off all other gas appliances. Clock the gas meter and
GHWHUPLQH WKH QXPEHU RI VHFRQGV UHTXLUHG WR FRQVXPH RQH
cubic foot of gas.
2.
3600 ÷ time (in seconds) = cu. ft. per hour.
3.
Then cu. ft. per hour x heating value of gas = input rate
(BTU/Hr). On installation without gas meters, check manifold
for proper pressure.
Note: The rate noted on the data plate is measured after 45 minutes
of continuous operation and adjusted for test conditions
such as temperature, and barometric pressure. The above
procedure is a check for correct conversion only.
3/$&(0(172)*$6&219(56,21/$%(/
Conversion label 2139 is to be filled out completely and placed
with the data plate attached near the valve.
If the appliance has not been installed, or a warranty card has not
been returned to Empire Comfort Systems, Inc., check off type of
gas converted to on card (for reference once the unit is installed).
Also, indicate conversion by adding "Conv." behind gas.
MODEL
AIR SHUTTER
SETTINGS
BURNER
ORIFICE
Opening "A"
Propane/LP
%9'
5/16"
(7.9mm)
1.35mm
P-289
%9'
5/16"
(7.9mm)
PP
P-208
%93
FULL OPEN
1.65mm
P-250
Air shutter settings shown are factory settings. Some venting
FRQILJXUDWLRQV PD\ UHTXLUH PLQRU DLU VKXWWHU DGMXVWPHQWV IRU
optimum performance.
“A”
