Emerson Rosemount ET310 Quick Start Manual Download Page 32 | Manualshive

Page: 32 / 52

background image

4. Remove the 4 protective caps from the 4 magnetic units one at a

time, by holding the magnetic unit and sliding the protective cap
away from the unit as displayed in the following figure. The magnetic
fixture does not need to be held after the protective caps are
removed.

A. Magnetic unit

B. Protective cap

C. Removing protective cap

5. Remove the protective cap from the sensor.
6. Carefully place the sensor with brackets inside the center of the

frame (as shown below). One person must hold the sensor until the
sensor securing bolts are fitted.

A. ET310 with brackets

B. Magnetic fixture

Quick Start Guide

January 2022

32

Emerson.com/Rosemount

«
...
30
31
32
33
34
...
»

Summary of Contents for Rosemount ET310





















































Reviews:

No comments

Related manuals for Rosemount ET310

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

Brand: Sanhua Pages: 3

Brand: U-Prox Pages: 3

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: TEL Pages: 26

Brand: Vimar Pages: 32

Brand: Seiko Pages: 30

ASC G Wi-Fi kit

Brand: Waeco Pages: 386

Brand: Trane Technologies Pages: 8

Brand: Olsen Pages: 4

Brand: Simplex Pages: 40

Brand: AirCycler Pages: 2

Torque Converter Lock-Up

Brand: TS Performance Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands