Emerson PACSystems IC695CPE400 Quick Start Manual Download | Manualshive

Page: 23 / 37

background image

21

IC695CPE400 Rackless CPU Quick Start Guide

GFK-3002G

Module Start-up

You Will Need:

▪

This PACSystems Rackless RX3i CPU.

▪

A compatible SELV 24Vdc, 48W power supply (72W if Energy Pack
attached).

▪

(Optionally) A compatible Energy Pack, IC695ACC403, and corresponding
cable.

▪

If no Energy Pack is to be attached, use the power supply cable described in
section

Connect to Power Supply.

▪

A DIN rail, typically mounted in an enclosure, as discussed above.
Alternately, mount the unit using the compatible panel-mount adaptor.

▪

A computer running PAC Machine Edition

™

(PME) configuration and

programming software. PME Version 9.70 SIM 16 or later supports the
CPE400. Version 9.50 SIM 5 is required for Hot Standby Redundancy.

▪

Ethernet cable for connecting the PME programmer computer to the
CPE400.

▪

Additional cables, as needed, to connect each port employed in the
application.

▪

A very small slotted screwdriver to secure the 24 Vdc mating connector.

▪

A T8 Torx screwdriver, if the micro-SD slot cover is to be removed. Note that
the cover must be replaced to achieve immunity from electrical noise.

▪

A T10 Torx screwdriver, if exchanging the mounting adaptors.

«
...
21
22
23
24
25
...
»

Summary of Contents for PACSystems IC695CPE400






































Reviews:

No comments

Related manuals for PACSystems IC695CPE400

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: ICP DAS USA Pages: 14

Brand: ICP DAS USA Pages: 25

Brand: ICP DAS USA Pages: 15

Brand: ICP DAS USA Pages: 8

Brand: IEI Technology Pages: 21

INTERNET PRIVACY PROTECTION

Brand: AlphaShield Pages: 49

Asynchronous SH7145F

Brand: Renesas Pages: 17

Brand: SIIG Pages: 20

IPAM-1600s Series

Brand: C-Com Pages: 148

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Xmart Pages: 8

Brand: Renesas Pages: 4

Brand: Digital Voice Systems Pages: 32

METERS AND MORE UM2241

Brand: ST Pages: 26

EK-Quantum Vector TUF RX 6800

Brand: ekwb Pages: 14

STM32MP157 Series

Brand: ST Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands