manualshive.com logo in svg

Emerson PACSystems IC695CPE400, Quick Start Manual

Share
Download
Emerson PACSystems IC695CPE400 Quick Start Manual Download Page 22

 

 
20 

IC695CPE400 Rackless CPU Quick Start Guide 

GFK-3002G 

CAUTION 

EQUIPMENT REPAIR REQUIRED 

–

 Internal components must be repaired at the 

factory; they are not field replaceable. Contact the support team at the link 
provided at the end of this document.

 

 

Overcurrent protection 

The function protects the internal circuitry from overcurrent conditions 
before serious damage can occur, such as overheating of the equipment. 
The fuse is rated for 4A continuous current. Once the sensed current 
reaches 40A, the fuse will blow after a period of 10ms to 100ms.  
 

CAUTION 

EQUIPMENT REPAIR REQUIRED 

–

 Internal components must be repaired at the 

factory; they are not field replaceable. Contact the support team at the link 
provided at the end of this document.

 

 

Grounding 

Grounding via the FGND connection on the 3-pin 24Vdc In power header is 
recommended (see section 

Connect to Power Supply

), but is not required if 

the CPE400 is mounted to a grounded metal panel. Furthermore, if an 
Energy Pack is connected, be sure to comply with grounding procedures as 
described in 

PACSystems RX3i Rackless Energy Pack IC695ACC403 Quick Start 

Guide, 

GFK-3000. 

Summary of Contents for PACSystems IC695CPE400






































Reviews:

No comments

Brands by name

Popular brands

Load more brands