Emerson PACSystems IC695CPE400 Quick Start Manual Download | Manualshive

Page: 20 / 37

background image

18

IC695CPE400 Rackless CPU Quick Start Guide

GFK-3002G

Installation in Hazardous Areas

Refer to the Installation and Maintenance Requirements document, GFK-
3004.

Connect to Power Supply

The 24Vdc power input connector is located
on the underside of the CPE400, as shown in
Figure 8. The signal pinouts are also
indicated.

The mating connector for the CPE400 24Vdc
power input is the 3-pin Phoenix 1827716
shown in Figure 9. The power supply cable
prepared by the user must use the specified
mating connector.

The positive

“+”

and negative

“

-

”

signals are

required. FGND is optional but
recommended.

For the mating connector, the compatible
conductor size is from 24AWG to 16AWG.
Strip the wires back 7mm before inserting
into the connector. Tightening torque for
the three signal screws is 2.2 in-Ibs
(0.248Nm). Secure the mating connector to
the power input connector via the two
captive screws provided.

Figure 8: 24 VDC Power
Input Connector

«
...
18
19
20
21
22
...
»

Summary of Contents for PACSystems IC695CPE400






































Reviews:

No comments

Related manuals for PACSystems IC695CPE400

Brand: 3Com Pages: 2

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: Q-See Pages: 2

Brand: 3Com Pages: 18

Brand: Supermicro Pages: 24

Brand: TRENDnet Pages: 12

Bluespoon 17-1000

Brand: Radio Shack Pages: 1

NVR41-4KS2 Series

Brand: Dahua Pages: 452

Brand: Alcatel-Lucent Pages: 12

Brand: Stepper Motor Canada Pages: 5

Brand: Intellinet Pages: 2

Brand: Xinje Pages: 76

Brand: Juniper Pages: 6

SPEEDTOUCH 110G

Brand: THOMSON Pages: 26

Brand: SilverStone Pages: 17

Brand: ADLINK Technology Pages: 69

EdgeSafe M40G1AC

Brand: Garland Pages: 159

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands