background image

 

 

IC695CPE400 Rackless CPU Quick Start Guide 

GFK-3002G 

Displays and Indicators (LEDs) 

OLED Display 

The monochrome organic light-emitting diode (OLED) display is used to 
display CPE400 system menus. It interacts with the DISP pushbutton, which 
jogs the cursor from one menu item to the next, and with the SEL 
pushbutton, which activates the currently indicated menu item for further 
action.  

The OLED display permits the user to: 

 

Display Ethernet LAN Settings: IPv4 address. 

 

Display the PLC firmware revision. 

 

Set/view PLC mode and view sweep time. 

 

Set the PLC mode to RUN/STOP with I/O Enabled/Disabled via the display. 

 

Note: the RUN and STOP pushbuttons activate the PLC Mode menu items 
per section 

Switches

. 

 

View whether all, some, or none of the PROFINET I/O devices are connected. 

 

Display EFA Settings: IPv4 address, subnet mask, gateway, MAC address, 
IPv6 address. 

 

Issue Field Agent Commands

Enter/Exit Configuration mode, Clear 

Configuration, Perform factory reset. 

 

View Field Agent Status: Off, Starting, Connecting, Connected, Connected-
ACT. 

 

View HSB Redundancy Mode and State (Release 9.30 and later) 

 

Command an HSB Redundancy Role Switch (Release 9.30 and later) 

Summary of Contents for PACSystems IC695CPE400






































Reviews: