background image

 

 

IC695CPE400 Rackless CPU Quick Start Guide 

GFK-3002G 

User Features 

The PACSystems

 RX3i CPE400, part of 

Emerson’s

 Industrial Internet 

Control System, is the industry’s first outcome optimizing controller. It 

augments real-time deterministic control with Field Agent technology, 
delivering near real time advice through market analysis, fleet and 
enterprise data, or asset/process knowledge to optimize the outcomes that 

today’s businesses require. The Predix™ enabled CPE400 provides reliable, 

secure communication and analytics using either cloud-based or edge-
based outcome optimizing apps. Controls can now be programmed to 
dynamically influence business outcomes, generate new forms of revenue, 
and improve profitability. 

 

The stand-alone CPE400 uses a quad-core microprocessor and real-time 
hypervisor technology to run real time deterministic control applications 
concurrently with Field Agent technology without any adverse impact of 
one over the other. 

o

 

A built-in RX3i PLC: 

o

 

User may program in Ladder Diagram, Structured Text, Function Block 
Diagram, or C. 

o

 

Contains 64Mbytes of configurable data and program memory. 

o

 

Supports auto-located Symbolic Variables that can use any amount of 
user memory. 

o

 

Reference table sizes include 32k bits for discrete %I and %Q and up to 
32k words each for analog %AI and %AQ. Bulk memory (%W) also 
supported for data exchanges. 

o

 

Supports up to 768 program blocks. Maximum size for a block is 
128KB. 

 

Field Agent technology is a platform for securely applying Predix 
applications and secure connectivity to the Predix Cloud as well as running 

Summary of Contents for PACSystems IC695CPE400






































Reviews: