Elk ELK-M1EZ8 Installation Manual Download Page 46

Page: 46 / 68

M1EZ8 Installation and Programming

Page 46

[Effective w/Firmware 4.3.6]

123456789012345678901234567890121234

WZnxxx:Sel

Prg

Wireless Zone

1234567890123456789012345678901212345

WZnxxx 01:=No

Enable Transmitr

1234567890123456789012345678901212345

WZnxxx02:=0

Supervision Type

1234567890123456789012345678901212345

WZnxxx 03:=No

Enable Option 1

1234567890123456789012345678901212345

WZnxxx 04:=No

Enable Option 2

123456789012345678901234567890121234

WZone = xxx

TransmtToEnroll

1234567890123456789012345678901212345

4:KeyfobSel

Prg

Event Definition

123456789012345678901234567890121234

Keyfob Button=1

1000=Event

1234567890123456789012345678901212345

2:Xmit Sel

Prg

Transmitter Opt

1234567890123456789012345678901212345

3:Learn Sel

Prg

WirelessTransmtr

123456789012345678901234567890121234

WZone = xxx Push
TransmiterButton

1234567890123456789012345678901212345

WZnxxx 05:=001

Keyfob User ID

Press the RIGHT arrow key to select 2:Transmitter Options.

Use the UP and DOWN arrow keys to locate a particular wireless transmitter. Press
the RIGHT arrow key to select and program the displayed transmitter.

Option 01 “Enable Transmitter” will be set to Yes whenever a new transmitter is
enrolled. To disable or remove this transmitter program this to No.

Option 02 selects the “Supervision Type” for the transmitter. 0=No Supervision,
1=Regular Supervision, 3=Fire Supervision. See receiver options R02 and R03 for
supervision time values. Default is 1.

Option 03 is used to disable the internal reed switch on the Caddx transmitter so that
an external switch may be hardwired to the transmitter.

Refer to the Caddx NX

Series Receiver Instructions for complete transmitter details.

Option 04 is used to select whether an external switch should be normally open (N/O)
or normally closed (N/C). For N/O set option to No. For N/C set option to Yes.

Refer

to the Caddx NX Series Receiver Instructions for complete transmitter details.

Option 05 sets the User ID that will be logged when a keyfob is used to arm or disarm.
Valid range is 001 to 255. If assigned as 001 to 099, the keyfob will mirror the keypad
user codes. If any of those users are programmed for opening/closing reports, they will
be reported regardless of whether a keypad code OR keyfob was used. NOTE: Since
there are no opening/closing report codes beyond user 99, any keyfob ID that is set
higher that 99 will utilize the opening/closing report code for User 99.

Press the RIGHT arrow key to select 3:Learn Wireless Transmitters.

Press the UP or DOWN arrow keys to locate the wireless zone that you wish to enroll.
Then press the RIGHT arrow key to continue.

Go to the transmitter and press the tamper or enroll button. The keypad should emit a
short tone when the transmitter becomes enrolled.

Press the RIGHT arrow key to select 4:Keyfob Event Definition

Press the UP or DOWN arrow keys to locate the keyfob button to program. There are
a total of 8 programmable buttons, however only 6 of the 8 may be used on the keyfob.
The valid activation events programmable for each button ranges from 0000-0030
(utilizing the Zone Definitions table) and 2001-2032 (utilizing Appendix A, Event Codes).

The standard buttons are as follows: Button 1 (Lock), 2 (Unlock), 3 (Light), and 4
(Asterisk). For Button 7 press a combination of buttons 1 & 2 together at the same
time. For Button 8 press a combination of buttons 3 & 4 together at the same time.

Button 3 on a keyfob can be changed to 5 by setting the transmitter Option 1 to Yes.
Button 4 on a keyfob can be changed to 6 by setting the transmitter Option 2 to Yes.

WWW.DIYALARMFORUM.COM