Ekinex EK-ES2-TP Applications Manual Download Page 60

Page: 60 / 100

Application manual

Air quality multisensor and regulator EK-ES2-TP

Release 1.0 - Updated: 14/02/2020

Application Manual

Page 60

Object name

Conditions

Dim.

Flags

DPT

Comm. Obj.

No.

Relative humidity

control



dehumidification



dehumidification

function = cooling

only

Dehumidification integration
control

Temperature

control



Settings



Thermostat

function = both
heating and
cooling,

Temperature
control



cooling



cooling type =

floor radiant panels
or ceiling radiant
panels,

Relative humidity
control



dehumidification



dehumidification
function = cooling
only

Integration = yes

1 bit

CR-T-

[1.001] switch

This object switches ON if (simultaneously) the relative humidity is greater than the relative
humidity setpoint and the room temperature is greater than the setpoint of the parameter

Temperature difference for integration.

Dehumidification control disable

Disable

dehumidification

control from bus =

yes

1 bit

C-W--

[1.002] boolean

Summary of Contents for EK-ES2-TP




































































































Search results

Summary of Contents for EK-ES2-TP

Reviews:

Ekinex EK-ES2-TP, Applications Manual, Page: 60 / 100

Search results

Summary of Contents for EK-ES2-TP

Reviews: