Ekinex EK-CG2-TP Applications Manual Download Page 51 | Manualshive

Page: 51 / 91

Ekinex EK-CG2-TP Applications Manual Download Page 51

Applicatio Manual

Universal Interface 4 DIN/NTC EK- CG2-TP

Revisione 1.0.0 - Aggiornato: 04/09/2017

© SBS S.p.A.

– Tutti i diritti riservati

MAEKCG2TP_EN

Pag. 51

Setpoint cyclic sending interval

no sending

[other values in the range 30 s … 120 min]

The setpoint value that can be sent cyclically is the actual one, depending on the
operating mode set manually by the user or automatically by another KNX
supervising device with the possibility of time scheduling. The actual setpoint value
takes also into account the actual state of the contacts window and presence
detection (if the corresponding functions are enabled).

Max manual temperature change

not allowed, ± 1°C, ± 2°C,

± 3°C

, ± 4°C, ±

5°C, ± 6°C, ± 7°C, ± 8°C, ± 9°C, ± 10°C

It defines the maximum range allowed for the manual change of the temperature
value.

End of manual operation

General Device operation as =

till first telegram from bus

stand-alone

[other values in the

range 30 min … 48 h]

Exit manual mode on setpoint from bus

no

/ si

It defines the exit from manual/forced mode in case of setpoint modification on bus
(communication objects index from 29 to 36)

Max setpoint temperature change

not allowed, ± 1°C, ± 2°C, ± 3°C, ± 4°C,

± 5°C, ± 6°C, ± 7°C, ± 8°C,

± 9°C

, ± 10°C

It defines the maximum time allowed for changing the values of temperature
setpoint in the several operating modes.

Duration of comfort extension

General Device operation as =

not allowed

, slave [other values in the

range 15 min … 4 h]

When device operation as = slave, if the operating mode forced by the time
scheduling is not comfort or building protection, this parameter defines the
maximum duration of temporary comfort before returning to the programmed
operating mode.

Scenes

disabled

/ enabled

Transmission delay after mode change

Valve protection function

disabled

/ enabled

It enables the function that activates the drive for the valve control during periods of
inactivity of the system.

Frequency

Valve protection function = enabled

once a day

once a week

once

a month

Time interval

Valve protection function = enabled

10 s

[other values in the range 5 s … 20 min]

Object name

Conditions

Dim.

Flags

DPT

Comm.

Obj.

No.

Actual setpoint

2 Byte

CR-T--

[9.001] temperature (°C)

27

Manual setpoint

2 Byte

C-W---

[9.001] temperature (°C)

28

«
...
49
50
51
52
53
...
»

Summary of Contents for EK-CG2-TP




























































































Reviews:

No comments