manualshive.com logo in svg

Ekinex EK-CG2-TP, Applications Manual, Page: 42 / 91

Share
Download
Ekinex EK-CG2-TP Applications Manual Download Page 42

Applicatio Manual 

                                Universal Interface 4 DIN/NTC EK- CG2-TP 

 

 

Revisione 1.0.0 - Aggiornato: 04/09/2017

 

© SBS S.p.A. 

– Tutti i diritti riservati 

MAEKCG2TP_EN 

Pag. 42 

 

 
 

9.2 Sensor temperature 

 
The Temperature Sensor tab contains the following parameters: 
 
• Enable the sensor 
• Filter type on internal data processing 
• Measured temperature correction 
• Minimum variation for sending value [K] 
• Cyclic delivery interval 
• Threshold 1 
• Threshold 2 

9.2.1 Parameters  and communication objects 

Parameter name 

 

Conditions 

 

Values 

 

Temperature sensor 

 

 

 

enabled 

 

disabled 

 

 

 

The temperature sensor is enabled as default.  

 

Filter type 

 

Temperature sensor = enabled 

 

low 

 

medium 

high 

 

 

 

Low = average value every 4 measurements 

 

Medium = average value every 16 measurements 

 

High = average value every 64 measurements 

 

Temperature offset 

 

Temperature sensor = enabled 

 

0°C

 

 

[range -5°C … +5°C] 

 

 

 

 

 

Minimum change of value to send [K] 

 

Temperature sensor = enabled 

 

0,5

 

 

[range 0 …5] 

 

 

 

If the parameter is set to 0 (zero),no value is sent after a change. 

 

Cyclic sending interval 

 

Temperature sensor = enabled 

 

no sending

 

 

[other values in the range 30 s … 120 min] 

 

 

 

 

 

Threshold 1 

 

not active 

 

Temperature sensor = enabled 

below 

 

above 

 

 

 

 

 

Value [°C] 

 

Temperature sensor = enabled,  

Threshold 1 = below or above 

 

7 

 

[range 0 … 50] 

 

 

 

 

 

Threshold 2 

 

Temperature sensor = enabled 

 

not active 

below above 

 

 

 

 

 

Value [°C] 

 

Temperature sensor = enabled,  

Threshold 2 = below or above 

 

45 

 

[range 0 … 50] 

 

 

 

 

 

Hysteresis 

 

Temperature sensor = enabled,  

 

Threshold 1 and/or Threshold 2 = 

below or above 

 

0,4 K 

 

[other values between 0,2 K and 3 K] 

 

 

 

 

 

Cyclic sending interval 

 

Temperature sensor = enabled,  

 

Threshold 1 and/or Threshold 2 = 

below or above 

 

no sending

 

 

[other values in the range 30 s … 120 min] 

 

 

 

 

 

Summary of Contents for EK-CG2-TP




























































































Reviews:

No comments