Efka SM210A5710, Instruction Manual

Page: 14 / 48

EFKA SM210A5710 14
Valid parameters if parameter 290 = 0 (synchronous stepping motor operation)
Parameter Functions max min Preset
002 c3 Number of stepping motor steps for metering device 9999 0 600
051 01- Value 1 of ratio on pushbutton 1 (V810/V820) 999 10 180
052 02- Value 2 of ratio on pushbutton 1 (V810/V820) 999 10 200
053 03- Value 3 of ratio on pushbutton 2 (V810/V820) 999 10 230
054 04- Value 4 of ratio on pushbutton 2 (V810/V820) 999 10 270
055 05- Value 5 of ratio on pushbutton 3 (V810/V820) 999 10 320
056 06- Value 6 of ratio on pushbutton 3 (V810/V820) 999 10 380
057 07- Value 7 of ratio on pushbutton 4 (V810/V820) 999 10 450
058 08- Value 8 of ratio on pushbutton 4 (V810/V820) 999 10 500
059 09- Value 9 of ratio on pushbutton 5 (V820) 999 10 550
060 10- Value 10 of ratio on pushbutton 5 (V820) 999 10 600
061 11- Value 11 of ratio on pushbutton 6 (V820) 999 10 650
062 12- Value 12 of ratio on pushbutton 6 (V820) 999 10 700
063 13- Value 13 of ratio on pushbutton 7 (V820) 999 10 750
064 14- Value 14 of ratio on pushbutton 7 (V820) 999 10 800
065 15- Value 15 of ratio on pushbutton 8 (V820) 999 10 850
066 16- Value 16 of ratio on pushbutton 8 (V820) 999 10 880
067 17- Value 17 of ratio on pushbutton 9 (V820) 999 10 900
068 18- Value 18 of ratio on pushbutton 9 (V820) 999 10 940
069 19- Value 19 of ratio on pushbutton 0 (V820) 999 10 960
070 --- Value 20 of ratio on pushbutton 0 (V820) 999 10 230
071 21- Value 21 of ratio on pushbutton 0 (V820) 999 0 208
112 n1 Fixed stepping motor speed w ith asynchronous operation [RPM] 600 0 100
113 n2 Fixed stepping motor speed with manual operation by means of pushb. A / B [RPM] 600 0 10
120 SnS From this sewing drive speed onwards signal M9 is emitted at the SM control 9990 0 0
130 rPd Select how to start metering device 7 1 1
131 bEE End of metering device at the start of the seam / seam end 2 0 0
132 Flo Lift sewing foot when feeding the tape On/Off 1 0 1
134 t7 Prolongation of blowing signal during metering device 9990 0 0
135 t5 Delay time until start of stepping motor for metering device [ms] 990 0 300
136 nFd Initiate end of stepping motor operation by thread trimming (see Parameter List) 1 0 1
137 nEd Initiate end of stepping motor operation by seam end (see Parameter List) 1 0 1
140 mbS Activate tape cutting by means of external pushbutton on input in1 / pedal –1 / 2 0 0
pedal -2
141 rbS Stepping motor runs parallel during tape cutting On/Off 1 0 0
142 t6 Activation time when operating the tape cutter manually at machine standstill [ms] 990 0 300
143 Ft2 Tape cutter until seam end or over time 1 0 0
152 SbS Function start tape tension. Last tape tension value or value selected by means 1 0 0
of pushbutton 1
190 mbS Ratios are selected via inputs in3 and in4 1 0 0
220 d01 Percental adaptation of the stepping motor speed up to 500 RPM 200 0 100
221 d02 Percental adaptation of the stepping motor speed up to 1000 RPM 200 0 100
222 d03 Percental adaptation of the stepping motor speed up to 1500 RPM 200 0 100
223 d04 Percental adaptation of the stepping motor speed up to 2000 RPM 200 0 100
224 d05 Percental adaptation of the stepping motor speed up to 2500 RPM 200 0 100
225 d06 Percental adaptation of the stepping motor speed up to 3000 RPM 200 0 100
226 d07 Percental adaptation of the stepping motor speed up to 3500 RPM 200 0 100
227 d08 Percental adaptation of the stepping motor speed up to 4000 RPM 200 0 100
228 d09 Percental adaptation of the stepping motor speed up to 4500 RPM 200 0 100
229 d10 Percental adaptation of the stepping motor speed up to 5000 RPM 200 0 100
230 c7 Correction factor when switching to fast tape feeding 9999 0 25
231 c8 Correction factor when switching to slow tape feeding 9999 0 90
291 810 Selection of insertable strip for V810 5 1 5
292 820 Selection of insertable strip for V820 5 1 5
293 tF1 Function of pushbutton A on the V810/V820 control panels 10 0 0
294 tF2 Function of pushbutton B on the V810/V820 control panels 10 0 0
See chapter “Parameter List” for values of the general parameters as well as for more detailed explanations of the above
parameters.
DC drive parameters:
Sign Function Parameter
n1 Positioning speed 110
n2 Maximum speed 111
n7 Trimming speed 116
t3 Start delay from lifted foot 202