manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Service Manual

Share
Download
EFI FIERY X3eTY 35C-KM Service Manual Download Page 70

62

The troubleshooting process

System software installation (continued)

Network port method:

Installation stalls for 5 
minutes (or longer) while 
downloading “file 1 of 2”

One of the following:

• Service switches are 

set to Normal mode

• Wrong or faulty 

RJ-45 cable

• Faulty motherboard

1. Make sure the Fiery X3eTY service switches are set to Service mode 

(toward “ON”).

If the service switches are in Normal mode (away from “ON”), click 
Cancel on the installer screen. Power off the Fiery X3eTY, set the service 
switches to Service mode, and click Finish on the installer screen. Then 
retry the installation.

2. Make sure you are using a cross-over RJ-45 cable.

The scanner interface cable is a cross-over type, and may be used for the 
installation.

If the cable appears damaged, replace it.

3. Clear the CMOS and power-up settings (see page 72).

4. Replace the motherboard.

Network port method:

Installation stalls for 20 
minutes (or longer) while 
downloading “file 2 of 2”

One of the following:

• Faulty HDD

• Faulty motherboard

1. Reseat the power and ribbon cables to the HDD.

2. Replace the HDD cable.

3. Replace the HDD.

4. Clear the CMOS and power-up settings (see page 72).

5. Replace the motherboard.

USB port method:

Installation stalls for 5 
minutes (or longer) while 
downloading “file 1 of 2”

One of the following:

• Service switches are 

set to Normal mode

• Wrong or faulty USB 

cable

• Faulty motherboard

1. Make sure the Fiery X3eTY service switches are set to Service mode 

(toward “ON”).

If the service switches are in Normal mode (away from “ON”), click 
Cancel on the installer screen. Power off the Fiery X3eTY, set the service 
switches to Service mode, and click Finish on the installer screen. Then 
retry the installation.

2. Make sure you are using a USB 2.0 cable.

If the cable appears damaged, replace it.

3. Replace the motherboard.

USB port method:

Installation stalls for 20 
minutes (or longer) while 
downloading “file 2 of 2”

One of the following:

• Faulty HDD

• Faulty motherboard

1. Reseat the power and ribbon cables to the HDD.

2. Replace the HDD cable.

3. Replace the HDD.

4. Replace the motherboard.

T

ABLE

 A

Fiery X3eTY error conditions (Continued)

Symptom

Possible cause

Suggested action 

Summary of Contents for FIERY X3eTY 35C-KM



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands