manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Service Manual

Share
Download
EFI FIERY X3eTY 35C-KM Service Manual Download Page 18

 

10

Accessing the Fiery X3eTY

 

T

 

O

 

 

 

OPEN

 

 

 

THE

 

 F

 

IERY 

 

X3

 

E

 

TY

 

C

 

AUTION

 

:

 

Before you touch any parts inside the Fiery X3eTY, make sure to wear an ESD 

grounding wrist strap and follow all ESD safety precautions. 

 

1.

Shut down the Fiery X3eTY and the print engine as described on page 8.

2.

Disconnect the external cables from the connector panel of the Fiery X3eTY.

3.

Disconnect the power cable from the Fiery X3eTY.

4.

Disconnect the two interface cables from the Fiery X3eTY.

5.

Remove the four screws that attach the Fiery X3eTY to the print engine. 

6.

Unhook and remove the Fiery X3eTY from the print engine. 

 

You must shift the Fiery X3eTY to the left to disconnect it from the print engine.

 

F

 

IGURE

 

 F

 

Accessing the Fiery X3eTY

For detailed information about removing/installing the Fiery X3eTY, see the 
print engine manufacturer’s installation instructions (not included in this service guide).

Interface cable connector

Print Engine

Fiery X3eTY

Power cable 
connector 
location

Interface cable connector

Hook location

Hook location

Summary of Contents for FIERY X3eTY 35C-KM



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands