manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Service Manual

Share
Download
EFI FIERY X3eTY 35C-KM Service Manual Download Page 65

57

The troubleshooting process

T

O

 

CHECK

 

INTERNAL

 

CONNECTIONS

C

AUTION

:

Before you touch any parts inside the print engine, make sure to wear an ESD 

grounding wrist strap and follow all ESD safety precautions. 

1.

Make sure that all Fiery X3eTY cables, devices, and DIMMs are present, intact, properly 
aligned, and well seated in their connectors. 

2.

Specifically check the following for proper installation in the pan: Power supply, HDD, 
Enclosed fans (2), Motherboard, Motherboard components (for list, see page 17).

3.

Specifically check motherboard cable and component connections:

4.

Specifically check all other cable connections in the pan: 

5.

After verifying connections, if one or more Fiery X3eTY components are still not 
receiving power, check the print engine and its internal interface to the Fiery X3eTY (see 
the print engine manufacturer’s documentation for information).

Motherboard silk-screened label  Component or cable

DIMM2

Socket for standard DIMM

DIMM1

Socket for upgrade option

SATA1

HDD cable

FAN2 (top fan); FAN3 (bottom fan) Enclosed fans with attached cables

N

OTE

: 

Top fan airflow is out; bottom fan airflow is in.

[on CPU, no label visible]

CPU cooling assembly

FAN1

CPU cooling assembly fan with attached cable

PC11

Interface board

J18

Power supply with attached cable

F4

Battery (see “Specifications” on page 49)

Front Panel [see footnote]

SW 2-wire cable attached to Soft power button
SW LED 2-wire cable attached to Soft power button

J11

Power supply with attached cable

JP22

Interface board location J632

J29

Interface board location J20

N

OTE

: 

“Front Panel” is silk-screened in two places on the motherboard: refer only to the label that 

appears on the edge of the board in very small text.

Location

Component or cable

Power switch, 4 lead, 2x2

Power supply with attached cable, split to two wires:
White wire to the lower lead corresponding to ON; 
Black wire to the lower lead corresponding to OFF

HDD

Power supply with attached cable, 4-pin, 1x4

HDD

HDD cable (to motherboard SATA1)

SW

SW LED

Front Panel

 

Summary of Contents for FIERY X3eTY 35C-KM



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands