manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Service Manual

Share
Download
EFI FIERY X3eTY 35C-KM Service Manual Download Page 47

39

System software

System software

The Fiery X3eTY system software is installed on the HDD at the factory. You must 
install system software if a more recent version is required, if you replace the HDD, or if 
you discover problems with the current system. To upgrade to a newer version of system 
software, you may install all system software over the LAN port or the USB port (see 
below) or use a USB flash drive (see page 45). 

System software installation reminders

When installing system software, keep in mind the following:

•

Fonts:

 Installing system software deletes all fonts that the customer has installed on the 

Fiery X3eTY. Only resident fonts are restored during system software installation. You 
can use Fiery Downloader to reinstall additional fonts.

To determine which additional fonts were downloaded to the Fiery X3eTY, print the 
Fonts List before you format the HDD and again after you complete the system 
software installation. Any fonts not listed after installation must be reinstalled. For 
more information, see 

Utilities

 on the User Documentation CD.

•

Language:

 Screens for installing system software are always displayed in English, even if 

the print engine is configured for another language.

•

Compatibility:

 The latest user software must be installed onto all computers that print 

to the Fiery X3eTY. Using incompatible versions of the system and user software may 
result in system problems.

Installing system software over the network port or USB port

The System Software CDs (2) contain the system software and Fiery System Software 
Installer. To install system software using the USB port or LAN port on the Fiery X3eTY, 
you need:

• Either:

– USB 2.0 cable—Maximum length: 5 meters (16.4 feet) 

or 

– For 100BaseTX—One Category 5 or higher Ethernet cross-over cable

(4-pair/8-wire, short-length)
For 1000BaseT—One Category 5e or higher Ethernet cross-over cable
(4-pair/8-wire, short-length)

• A Windows XP/2000 computer with:

– A CD-ROM drive, built in or attached

– Support for 100BaseTX or 1000BaseT and/or USB 2.0

Summary of Contents for FIERY X3eTY 35C-KM



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands