manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Service Manual

Share
Download
EFI FIERY X3eTY 35C-KM Service Manual Download Page 45

37

Verifying connection to the network

Verifying connection to the network

The Fiery X3eTY provides twisted pair connectivity to an Ethernet network. This section 
describes how to connect the Fiery X3eTY to the network and then print a few test 
documents in order to verify the connection.

Depending on your network speed, the following unshielded twisted pair (UTP) 
network cables are supported:

• For 10BaseT, Category 3 or higher

• For 100BaseTX, Category 5 or higher (4-pair/8-wire, short-length)

• For 1000BaseT, Category 5e or higher (4-pair/8-wire, short-length)

N

OTE

:

If the print engine is 230V, use a shielded network cable.

The network cable connects to the LAN port on the connector panel of the Fiery X3eTY 
(see Figure P).

F

IGURE

 P

Network connectors and service switches

LAN port for 10/100/1000BaseT

twisted pair Ethernet

Service switches

USB Type B port for connection

to a computer for system

software installation or printing

USB Type A ports (3) Either can

connect to a USB flash drive for

system software installation

Summary of Contents for FIERY X3eTY 35C-KM



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands