manualshive.com logo in svg

EFI FIERY X3eTY 35C-KM, Service Manual

Share
Download
EFI FIERY X3eTY 35C-KM Service Manual Download Page 67

59

The troubleshooting process

Fiery X3eTY starts up but 
the Fiery screens on the 
Control Panel are 
unavailable for more than 
10 minutes

One of the following:

• Faulty connection 

between Fiery  X3eTY 
and copier

• Corrupt system 

software

• Faulty copier 

interface board

1. Check and reseat the copier interface cable between the Fiery X3eTY and 

the copier.

2. Replace the copier interface cable.

3. Reinstall system software.

4. Replace the copier interface board.

Fiery X3eTY starts up, 
and stays on, but does not 
reach Idle

One of the following:

• Service switches are 

set to Service mode

• System software is 

corrupt

• HDD is faulty

• Missing or faulty 

DIMM(s), or faulty 
DIMM connections

• Motherboard is faulty 

• CPU missing or 

faulty

1. Make sure the Fiery X3eTY service switches are set to Normal mode 

(away from “ON”).

2. Power off/on the copier.

3. Reinstall system software.

4. Reseat the power and ribbon cables to the HDD.

5. Replace the HDD cable.

6. Replace the HDD.

7. Check the DIMM(s) and reseat them to remove any oxidation on the 

connectors.

8. If you have two DIMMs installed, determine if a DIMM is at fault:

Remove the DIMM currently installed in socket DIMM1, and reboot the 
system. Then reboot again with the other DIMM installed in DIMM2. 
If the problem is solved by one of the DIMMs, replace the other DIMM.

If the problem persists for both DIMMs, proceed to the next step.

9. Clear the CMOS and power-up settings (see page 72).

10. Replace the motherboard.

11. Replace the CPU.

User authentication 
feature of the print engine 
does not work

• Faulty interface 

connections

• Check connections of Interface board and replace associated cables or 

copier interface board, if necessary.

T

ABLE

 A

Fiery X3eTY error conditions (Continued)

Symptom

Possible cause

Suggested action 

Summary of Contents for FIERY X3eTY 35C-KM



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands