EFI E-46A Installation And Service Manual Download Page 128

Page: 128 / 134

128

Installation and Service Guide: Color Controller E-46A

Specifications

This chapter provides an overview of the E-46A hardware features.

Hardware features

•

Intel Core i5-6500, quad core 3.2GHz CPU (up to 3.6GHz with Turbo Boost enabled)

•

RAM: 8GB (2

4GB) DDR4 RAM

•

1TB hard disk drive standard

•

DVD-RW drive

•

RJ-45 connector for 10BaseT/100BaseTX/1000BaseT Mbs connectivity over twisted pair cable (upper port)

Physical specifications

•

Operating Environment:

•

Temperature: +5

C to +40

•

Relative Humidity: 10%-85% (non-condensing)

•

Power Supply Voltage/Frequency Input: 100-240V @ 50-60Hz

•

Power Supply Current Input: 100V @ 6A Max.; 240V @ 3A Max.

•

Rated Power Consumption: 350W

•

Dimensions (Depth x Height

Width):

46.36 cm (18.25 in.)

52.71 cm (20.75 in.)

23.50 cm (9.25 in.)

•

Weight: 16.56 kg (36.5 lb.)

Networking and connectivity

•

Supports AppleTalk and TCP/IP protocols simultaneously.

Note:

AppleTalk is supported only for downloading fonts.

Safety and emissions compliance

The E-46A has been certified to meet or surpass the following government standards:

Safety approvals

•

IEC 60950-1:2005 (Second Edition) + Am 1:2009 + Am2:2013

Summary of Contents for E-46A







































































































































Search results

Summary of Contents for E-46A

Reviews:

Related manuals for E-46A

Brands by name

Popular brands

EFI E-46A, Installation And Service Manual

Search results

Summary of Contents for E-46A

Reviews:

Related manuals for E-46A

Brands by name

Popular brands