EFI E-46A Installation And Service Manual Download Page 106

Page: 106 / 134

106

Installation and Service Guide: Color Controller E-46A

Installing System Software

Rotate the Fiery QuickTouch 45 degrees so that the pin hole (download button) at the bottom of the Fiery

QuickTouch is accessible.

Figure 44:

Reset and download buttons on the Fiery QuickTouch

Using two paper clips, press the download button.

While pressing the download button, press the reset button on the right side of the Fiery QuickTouch, next to the

USB ports.

The Fiery QuickTouch enters the download mode.

Access the “C:\Glance\image\NX-

<version_number>

-system_update” folder, and double-click the “

flash.bat

” file.

Wait until the Fiery QuickTouch completes the installation and displays the Home screen. The installation may

take approximately 10 to 15 minutes to complete.

After installing or updating the system software

Restore the dongles and devices that you removed in a previous step, if applicable.

If the power synchronization is disabled, enable the power synchronization (see

page 23

Start the E-46A (see

page 42

Install any required software patches by System Updates (see

page 108

Reset button

Download button (accessible when Fiery QuickTouch is rotated about 45 degrees)

Summary of Contents for E-46A







































































































































Search results

Summary of Contents for E-46A

Reviews:

Related manuals for E-46A

Brands by name

Popular brands

EFI E-46A, Installation And Service Manual

Search results

Summary of Contents for E-46A

Reviews:

Related manuals for E-46A

Brands by name

Popular brands