EFI E-46A Installation And Service Manual Download Page 85

Page: 85 / 134

Installation and Service Guide Color Controller E-46A

Replacing parts

Release the front latches on both side of the DVD drive by squeezing the levers, and pull the DVD drive out of the

slot.

Figure 42:

Removing/replacing the DVD drive

If you are replacing the DVD drive with new one, remove the eight screws on the side of the DVD drive and remove

the ears.

Set aside the screws so that you can replace them later.

To replace the DVD drive

If you are installing the new DVD drive, attach the ears on both side of the DVD drive using the eight screws you

removed earlier.

Insert the DVD drive into the front panel cutout until the latch snaps.

Connect the power/data cables to the connectors on the back of the DVD drive.

Make sure that the other ends of the power and data cables are connected to the power supply and SATA0 (J50) on

the motherboard.

Latch lever (1/2)

DVD drive

Summary of Contents for E-46A







































































































































Search results

Summary of Contents for E-46A

Reviews:

Related manuals for E-46A

Brands by name

Popular brands

EFI E-46A, Installation And Service Manual

Search results

Summary of Contents for E-46A

Reviews:

Related manuals for E-46A

Brands by name

Popular brands