manualshive.com logo in svg

EFI E-45, Installation And Service Manual, Page: 54 / 126

Share
Download
EFI E-45 Installation And Service Manual Download Page 54

54

Installation and Service Guide: Color Controller E-45

Replacing parts

Fiery QuickTouch display module

Fiery QuickTouch is attached to the top panel of the E-45.

Follow the directions to remove the chassis covers. See 

“Opening the E-45”

 on page 50. You will need to remove the side 

covers, then the front cover before you will be able to release the top bezel with the Fiery QuickTouch attached. 

To remove the Fiery QuickTouch

1

Follow the instructions to remove the side and front chassis covers.

2

To remove the top bezel, slide the bezel forward and release it from the top of the chassis.

3

Stabilize the unit and set the Fiery QuickTouch on its side atop the unit.

4

Remove the two connectors to the Fiery QuickTouch.

a

Remove the tie-wrap that bundles the power cable and a tab on the support bracket for USB connector. 

Caution: 

 It is highly recommended that you use a screwdriver with a magnetic tip when removing or replacing 

screws on the Fiery QuickTouch. If you do not, the screws you remove or replace might fall inside the Fiery 
QuickTouch device. 

Summary of Contents for E-45































































































































Reviews:

No comments