manualshive.com logo in svg

Eaton Power Xpert 9395 UPS, Installation And Operation Manual

Share
Download
Eaton Power Xpert 9395 UPS Installation And Operation Manual Download Page 56

UPS Installation Plan and Unpacking

3-28

Power Xpert 

TM 

9395 UPS (450–825 kVA) Installation and Operation Manual

  

  164201725—Rev 10    

www.eaton.com/powerquality

2.

Use a forklift or pallet jack to move the packaged cabinet to the installation site, or as close as possible, 
before unpacking. If possible, move the cabinet using the pallet. Insert the forklift or pallet jack forks from 
the right side of the pallet (facing the cabinet), between the supports on the bottom of the pallet (see 
Figure 3-13 for the UPS cabinet center of gravity measurements). If the cabinet must be moved using the 
cabinet front or rear fork lift slots, see the caution statement at the beginning of this procedure.

CAUTION

Do not tilt the UPS cabinet more than 10º from vertical or the cabinet may tip over.

3.

Set the pallet on a firm, level surface, allowing a minimum clearance of 3m (10 ft) on each side for 
removing the cabinet from the pallet.

4.

Remove the protective covering from the cabinet.

5.

Remove the packing material, and discard or recycle in a responsible manner.

6.

Inspect the contents for any evidence of physical damage, and compare each item with the Bill of Lading. 
If damage has occurred or shortages are evident, contact an Eaton service representative immediately to 
determine the extent of the damage and its impact on further installation.

NOTE

The ISBM and UPM sections are shipped with debris shields covering the 

ventilation grills on top of the sections (see Figure 3-14). Do not remove the debris 
shields until installation is complete.

NOTE

While waiting for installation, protect the unpacked cabinet from moisture, dust, and 

other harmful contaminants. Failure to store and protect the UPS properly may void 
your warranty.

Summary of Contents for Power Xpert 9395 UPS



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands