background image

3

IMPORTANT INFORMATION

• 

Caution: parts of this product may become very hot and cause burns. Extra care should 

be taken if children and vulnerable people are present. 

• 

Children under 3 years of age should be kept away from this appliance unless they are 

under continuous supervision.

• 

Children aged between 3 and 8 years old must only switch the appliance ON or OFF, 

provided that the appliance has been placed or installed in a normal position and that 

these children have or have been instructed to use the device safely and understand the 

potential hazards. 

• 

Children between 3 and 8 years old should not plug in, adjust, clean, or carry out user 

maintenance.

• 

This  device  can  be  used  by  children  at  least  8  years  of  age  and 

by  persons  with  reduced  physical,  sensory  or  mental  abilities  or 

no  experience  or  knowledge,  if  they  are  properly  supervised  or

 

if  instructions  for  the  safe  use  of  the  device  have  been  given  to  them  and  the  risks 

involved have been addressed. 

• 

Children should not play with the device. 

• 

Cleaning and user maintenance should not be performed by unattended children.

• 

To avoid danger to very young children, it is recommended to install this towel heater so 

that the lowest heating bar is at least 600 mm above the floor.

• 

This  appliance  must  only  be  connected  according  to  the  rules  and  standards  in 

application, by an authorized person.

• 

If the power cable is damaged, it must be replaced by the manufacturer, its after-sales 

service or similarly qualified persons in order to avoid a hazard.

• 

All work on the electrical parts must be carried out by a qualified professional.

• 

At  the  first  heating,  a  slight  odor  may  appear  corresponding  to  the  evacuation  of  any 

traces related to the manufacture of the device.

• 

A  power  management  system  or  power  failure  is  not  compatible  with  our  devices.  It 

damages the thermostats.

• 

For safety reasons, it is strictly forbidden to refill the towel rails. If necessary, contact the 

manufacturer’s after-sales service or a qualified professional.

• 

To ensure proper operation and avoid overheating, the electronic controller must not be 

covered by a towel or a bathrobe.

• 

Before servicing the towel rail, turn it off and let it cool down. Never use abrasives and 

solvents.

• 

The towel rail is filled with a heat transfer fluid dangerous to health if swallowed. In the 

event of a leak, contact your installer and take any precautionary measures to prevent 

any ingestion of fluid by users, especially young children and vulnerable persons.

Summary of Contents for Colorado DGi+ 450





















Reviews: