manualshive.com logo in svg

DTS INSIGHT FR830, Instruction Manual

Share
Download
DTS INSIGHT FR830 Instruction Manual Download Page 59

 

58

11. Notes and Cautions for Using FR830

 

 

(1) The Control Module FR830 is built for NETIMPRESS.    DO NOT use this Control Module for 

any flash microcomputer programmers other than the NETIMPESS series.

 

 

(2) The Control Module FR830 is designed for the specific microcomputer.

 

Do  not  use  this  Control  Module  for  programming  microcomputers  other  than  the  specified 
microcomputer.  Using  this  definition  program  for  microcomputers  other  than  the  specified 
microcomputer would damage your target system.

 

 

(3) NETIMPRESS consumes power of several mA from Tvccd terminal to drive the interface IC 

with the target system (IC inside NETIMPRESS).

 

 

(4)  DO  NOT  insert  or  remove  the  Control  Module  while  the  Device  Functions  or  the  Function 

operation is being executed.

 

Ejecting the Control Module during the operation would cause a serious damage to the data 
in the Control Module.

 

 

(5) Use NETIMPRESS with the Control Module inserted into it.

 

 

 

 

Summary of Contents for FR830




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands