manualshive.com logo in svg

DTS INSIGHT FR830, Instruction Manual

Share
Download
DTS INSIGHT FR830 Instruction Manual Download Page 54

 

53

 

Error Message

Causes & Measures

112D 
UART 

BAUDRATE 

SETTING ERR 

Cause

 

You cannot use the specified baud rate.

 

Measure

 

Change the baud rate setting.

 

112E 
UNSUPPORTED 
BAUD RATE 

Cause

 

Programmed  with  the  programmer  that  does  not 
support  UART  communication  baud  rate  higher  than 
1000000bps.

Corrective 
action

 

UART  communication  baud  rate  higher  than 
1000000bps can be used with only NETIMPRESS next.
Change the communication baud rate.

 

112F 
UNSUPPORTED 
BAUD RATE 

Cause

 

Programmed  with  NETIMPRESS  next  that  does  not 
support  UART  communication  baud  rate  higher  than 
1000000bps.

 

The version of NETIMPRESS next may be old.

 

Corrective 
action

 

Please contact our Support Center.

 

113E 
OBJECT  FILE  NOT 
DOWNLOAD 

Cause

 

Object file is not downloaded in object file programming 
mode.

 

Measure

 

Download the object file.

 

 

 

 

 

Summary of Contents for FR830




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands