manualshive.com logo in svg

DTS INSIGHT FR830, Instruction Manual

Share
Download
DTS INSIGHT FR830 Instruction Manual Download Page 23

 

22

3.

  

Connecting to a Target System and Connector

 

 

3.1.  Signal List

 

The following table shows the signal list of the target end of the target probe connector when 

you use FR830.

 

 

Microcomputer 

Signal 

 

NET IMPRESS Standard Signal

 

Microcomputer 

Signal 

 

EVSS

 

GND

 

15

 

1

 

GND

 

EVSS

 

 

TVpp1

 

16

 

2

 

TVccd

 

EVCC

 

 

TVpp2

 

17

 

3

 

Vcc

 

 

Watchdog pulse

 

WDC

 

(18)

 

(4)

 

TRES

 

Positive/TRES

 

 

TAUX3

 

TVpp1c

 

19

 

5

 

/TRES

 

/RESET

 

FLMD0

 

TAUX4

 

TVpp2c

 

20

 

(6)

 

TCK

 

FPCK

 

(JP0_2)

 

 

reserved

 

21

 

7

 

reserved

 

 

 

reserved

 

22

 

8

 

reserved

 

 

 

TAUX

 

23

 

9

 

TAUX2

 

(TRW)

 

 

 

TBUSY

 

24

 

(10)

 

/TICS

 

Multiplexer

 

 

TI0

 

25

 

11

 

TAUX5

 

(/TOE)

 

 

 

TVccs

 

26

 

(12)

 

TMODE

 

FLMD1

 

FPDT

 

(JP0_1)

 

TRXD

 

(27)

 

13

 

TTXD

 

FPDR

 

(JP0_0)

 

EVSS

 

GND

 

28

 

14

 

GND

 

EVSS

 

Target Probe Signal List (FR830)

 

 

1. Be sure to connect all the signals marked with a circle “○ “ to the target system.

 

2. For the signals in parentheses, connect them only when necessary.

 

3. For the signals not marked with “ 

〇

  “ or not in parentheses, be sure not to connect them to a 

circuit of the target system.

 

For inquiry about the detail information, please contact our Support Center.

 

4. For interface circuits of each signal, see “Instruction Manual” of the NET IMPRESS main unit.

 

 

Summary of Contents for FR830




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands