Domino G Series Page 94 Product Manual Download

Page: 94 / 172

POWER SAVE SETTINGS

To view the power save settings:

1. From the

Home

screen, select the

Settings

icon:

2. Select the

Power Save Settings

icon:

Monitor

To view and edit the power save monitor settings:

1. From the

Home

screen, select the

Settings

icon:

2. Select the

Power Save Settings

icon:

2.
3. Adjust the settings listed below:

Name

Description

Brightness

Use the slider bar to adjust the screen brightness.

Power save

Turn power save settings

Off

. When enabled, the

Darken screen

and

Turn off screen

settings will be available.

Darken screen

After a set time of no action, the screen will darken to save

power.
The screen will darken by 50%.
The screen will go back to the set brightness value when

touched.
The available settings are:

•

30 seconds

•
•

1 minute

•
•

5 minutes

•
•

Never

•

Turn off screen

After a set time of no action, the screen will turn off to save

power.
The screen will go back to the set brightness value when

touched.
The available settings are:

•

10 minutes

•
•

30 minutes

•
•

1 hour

•
•

Never

•

INSTALLATION

EPT077343 EN - Issue 1 - 11 November 2022

Summary of Contents for G Series













































































































































































Search results

Summary of Contents for G Series

Reviews:

Related manuals for G Series

Brands by name

Popular brands

Domino G Series, Product Manual

Search results

Summary of Contents for G Series

Reviews:

Related manuals for G Series

Brands by name

Popular brands