DOGA MDT Series Instruction Manual Download Page 63

Page: 63 / 84

Instructions manual

/ MDT Series & MDTC38

60429 08/21

7.15 Remote : Back up / Restore / Power Reset / Factory reset

◆

Backup

Parameter back up save in SD-Card.

Save on \SD-Card\PARAM folder.

Back up file name : yyyymmdd.csv

Only one file per day (latest backup erase previous one)

◆

Restore

Load backup file from SD-Card.

Only compatible with files saved with controller backup (see

above)

Do not restore with backup files saved with Webserver or

ParaMon MDTC

Back up and restore should have been made with same

controller firmware version

◆

Power reset

Power reset provide the equal effect of system rebooting by power switch OFF and ON.

◆

Factory reset

All parameter reset, when click this button, reboot system and all parameter(setting) initialized by

factory setting

20200530.csv

20200610.csv

Summary of Contents for MDT Series





















































































Search results

Summary of Contents for MDT Series

Reviews:

Related manuals for MDT Series

Brands by name

Popular brands

DOGA MDT Series, Instruction Manual

Search results

Summary of Contents for MDT Series

Reviews:

Related manuals for MDT Series

Brands by name

Popular brands