DOGA MDT Series Instruction Manual Download Page 58

Page: 58 / 84

Instructions manual

/ MDT Series & MDTC38

60429 08/21

7.13 Monitoring

To monitor fastening data and I/O, click

and go to

There are three(3) real-time monitoring menu and one error history.

Graph : torque, Angle, Speed and current

Input & output status

Network : RS-232 & Ethernet settings

Error : latest 8 error history

◆

Graph (Torque curve) monitoring

Two channel data curve for Current, Torque, Angle, Speed

The sampling rate is 1ms (0.001second) for limitless data.

Auto scale will display all data on one single screen by
changing real-time sampling rate automatically.

The curve is displayed during the operation time and
completed by operation stop.

So the graph monitoring does not make any time delay
issue for the operation.

Summary of Contents for MDT Series





















































































Search results

Summary of Contents for MDT Series

Reviews:

Related manuals for MDT Series

Brands by name

Popular brands

DOGA MDT Series, Instruction Manual

Search results

Summary of Contents for MDT Series

Reviews:

Related manuals for MDT Series

Brands by name

Popular brands