manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 346

120,000 Miles (192,000 km) or 96 Months Maintenance Service Schedule

❏

Check the Diesel Exhaust Fluid (DEF) tank, refill if necessary.

❏

Rotate tires.

❏

Replace engine fuel filter element.

❏

Replace chassis mounted fuel filter element.

❏

Lubricate front drive shaft fitting (4x4).

❏

Lubricate outer tie rod ends.

❏

Inspect the wheel bearings.

❏

Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness
or end play; replace if necessary.

❏

Inspect the front and rear axle surfaces. If gear oil leakage is suspected, check the fluid level. If using your vehicle for police,
taxi, fleet, off-road or frequent trailer towing change the axle fluid.

❏

Change the automatic transmission fluid and filter(s).

❏

Change the manual transmission fluid if using your vehicle for any of the following: police, fleet, or frequent trailer towing.

❏

Change the transfer case fluid (4x4).
** Under no circumstances should oil change intervals exceed 15,000 miles (24 000 km) or six months or 500 Hours, whichever
comes first.

Odometer Reading

Date

Repair Order #

Dealer Code

Signature, Authorized Service Center

344

MAINTENANCE SCHEDULE

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands