manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 220

1. If the engine stalls after the initial start, the ignition

must be turned to the OFF position for at least five
seconds and then to the ON position to recycle the
manifold heaters.

NOTE:

Excessive white smoke and poor engine perfor-

mance will result if manifold heaters are not recycled.

2. Heat generated by the manifold heaters dissipates

rapidly in a cold engine. If more than two minutes
pass between the time the “Wait To Start” telltale turns
off and the engine is started, recycle the manifold
heaters by turning the ignition switch to the OFF
position for at least five seconds and then back ON.

3. If the vehicle is driven and vehicle speed exceeds

19 mph (31 km/h) before the manifold heater post-
heat (after start) cycle is complete, the manifold heat-
ers will shut off.

4. If the engine is started before the “Wait To Start”

telltale turns off, the preheat cycle will turn off.

5. If the engine is cranked for more than 10 seconds, the

post-heat cycle will turn off.

NOTE:

•

Engine idle speed will automatically increase to 1,000
RPM and engage the Variable Geometry Turbocharger
at low coolant temperatures to improve engine warm-
up.

•

When a diesel engine is allowed to run out of fuel or
the fuel gels at low temperatures, air is pulled into the
fuel system. If your engine has run out of fuel, refer to
“Maintenance Procedures/Priming If The Engine Has
Run Out Of Fuel” in “Maintaining Your Vehicle” for
further information.

218

STARTING AND OPERATING

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands