manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 300

Refer to “Fluids, Lubricants, and Genuine Parts” in
“Maintaining Your Vehicle” for further information.

You can receive assistance in locating DEF in the United
States by calling 866-RAM-INFO (866-726-4636). In
Canada call 1–800–465–2001 (English) or 1–800–387–9983
(French)

Maintenance-Free Batteries

The top of the maintenance-free batteries are perma-
nently sealed. You will never have to add water, nor is
periodic maintenance required.

NOTE:

Replacement batteries should both be of equal

capacity to prevent damage to the vehicle’s charging
system.

CAUTION!

It is essential when replacing the cables on the
battery that the positive cable is attached to the
positive post and the negative cable is attached to the
negative post. Battery posts are marked (+) positive
and negative (-) and are identified on the battery
case. Also, if a “fast charger” is used while the battery
is in vehicle, disconnect both vehicle battery cables
before connecting the charger to the battery. Do not
use a “fast charger” to provide starting voltage.

WARNING!

Battery posts, terminals, and related accessories con-
tain lead and lead compounds. Always wash hands
after handling the battery.

298

MAINTAINING YOUR VEHICLE

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands