manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 106

If more than two ounces or 60 milliliters of fuel have been
drained, follow the directions for “Priming If The Engine
Has Run Out Of Fuel.”

Underbody Mounted Fuel Filter Replacement

NOTE:

Using a fuel filter that does not meet the manu-

facturer’s filtration and water separating requirements
can severely impact fuel system life and reliability.

CAUTION!

•

Diesel fuel will damage blacktop paving surfaces.
Drain the filter into an appropriate container.

•

Do not prefill the fuel filter when installing a new
fuel filter. There is a possibility debris could be
introduced into the fuel filter during this action. It
is best to install the filter dry and allow the in-tank
lift pump to prime the fuel system.

1 — Water in Fuel Drain
2 — Fuel Filter Access

1. Turn engine off.

2. Place a drain pan under the fuel filter assembly.

Fuel Filter Assembly

104

MAINTAINING YOUR VEHICLE

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands