Dodge 2015 RAM Owner'S Manual Download Page 194

Page: 194 / 366

Driver Information Display (DID) — 7” Display

The Driver Information Display (DID) display is located
in the center portion of the cluster and consists of eight
sections:

1. Main Screen — The inner ring of the display will

illuminate in grey under normal conditions, yellow for
non critical warnings, red for critical warnings and
white for on demand information.

2. Audio Information and Submenu Information —

Whenever there are submenus available, the position
within the submenus is shown here.

3. Selectable Information (Compass, Temp, Range to

Empty, Trip A, Trip B, Average MPG, Trailer Trip
(distance only), Trailer Brake Gain).

4. Air Suspension Status – If Equipped

5. Transmission Gear Position Indicator (PRND)

6. Status Menu Icons

7. Telltales/Indicators

8. 4WD Status

192

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2015 RAM















































































































































































































































































































































































Search results

Summary of Contents for 2015 RAM

Reviews:

Brands by name

Popular brands

Dodge 2015 RAM, Owner'S Manual

Search results

Summary of Contents for 2015 RAM

Reviews:

Brands by name

Popular brands