Dodge 2015 RAM Owner'S Manual Download Page 294

Page: 294 / 366

5. Remove lid using a socket or strap wrench. Rotate

counterclockwise for removal. Remove used o-ring
and discard it.

6. Remove the used filter cartridge from the housing and

dispose of according to your local regulations.

7. Wipe clean the sealing surfaces of the lid and housing.

8. Install new o-ring back into ring groove on the filter

housing and lubricate with clean engine oil.

9. Remove new filter cartridge from plastic bag and

install into housing.

NOTE:

Do not remove cartridge from bag until you reach

this step in order to keep cartridge clean.

10. Push down on the cartridge to ensure it is properly

seated.

Do not pre-fill the filter housing with fuel.

11. Install lid onto housing and tighten to 22.5 ft lbs (30.5

N.m). Do not overtighten the lid.

12. Prime the engine using the procedure in “Priming If

The Engine Has Run Out Of Fuel.” Then start the
engine and confirm there are no leaks.

292

MAINTAINING YOUR VEHICLE

Summary of Contents for 2015 RAM















































































































































































































































































































































































Search results

Summary of Contents for 2015 RAM

Reviews:

Brands by name

Popular brands

Dodge 2015 RAM, Owner'S Manual

Search results

Summary of Contents for 2015 RAM

Reviews:

Brands by name

Popular brands