manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 297

Priming If The Engine Has Run Out Of Fuel

WARNING!

Do not open the high pressure fuel system with the
engine running. Engine operation causes high fuel
pressure. High pressure fuel spray can cause serious
injury or death.

1. Add a substantial amount of fuel to the tank, approxi-

mately 2 to 5 gal (8L to 19L).

2. Turn ignition switch to the start position to engage

starter for one second, return ignition switch to run
position. This will activate in tank fuel pump for
approximately 15 seconds. Repeat this process twice.

3. Start the engine using the “Normal Starting” proce-

dure. Refer to “Starting Procedures” in “Starting and
Operating” for further information.

CAUTION!

Do not engage the starter motor for more than 15
seconds at a time. Allow two minutes between the
cranking intervals.

NOTE:

The engine may run rough until the air is forced

from all the fuel lines.

WARNING!

Do not use alcohol or gasoline as a fuel blending
agent. They can be unstable under certain conditions
and be hazardous or explosive when mixed with
diesel fuel.

6

MAINTAINING YOUR VEHICLE

295

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands