manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 108

CAUTION!

The starter motor will engage for approximately 30
seconds at a time. Allow two minutes between crank-
ing intervals.

NOTE:

The engine may run rough until the air is forced

from all the fuel lines.

WARNING!

Do not use alcohol or gasoline as a fuel blending
agent. They can be unstable under certain conditions
and be hazardous or explosive when mixed with
diesel fuel.

CAUTION!

Due to lack of lubricants in alcohol or gasoline, the
use of these fuels can cause damage to the fuel
system.

NOTE:

•

We recommend you use a blend of up to 5% biodiesel,
that meets ASTM specification D-975 with your diesel
engine. Use of biodiesel mixture in excess of 20% can
negatively impact the fuel filter’s ability to separate
water from the fuel, resulting in high pressure fuel
system corrosion or damage.

•

In addition, commercially available fuel additives are not
necessary for the proper operation of your diesel engine.

106

MAINTAINING YOUR VEHICLE

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands