manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 265

WARNING!

•

Never have any smoking materials lit in or near the
vehicle when the fuel filler cap is removed or the
tank filled.

•

Never add fuel to the vehicle when the engine is
running.

Avoid Using Contaminated Fuel

Fuel that is contaminated by water or dirt can cause
severe damage to the engine fuel system. Proper main-
tenance of the engine fuel filter and fuel tank is essential.
Refer to “Maintenance Procedures” in “Maintaining Your
Vehicle” for further information.

Bulk Fuel Storage — Diesel Fuel

If you store quantities of fuel, good maintenance of the
stored fuel is also essential. Fuel contaminated with
water will promote the growth of “microbes.” These

microbes form “slime” that will clog the fuel filtration
system and lines. Drain condensation from the supply
tank and change the line filter on a regular basis.

NOTE:

When a diesel engine is allowed to run out of

fuel, air is pulled into the fuel system.

If the vehicle will not start, refer to “Maintenance
Procedures/Priming If The Engine Has Run Out Of Fuel”
in “Maintaining Your Vehicle” for further information.

WARNING!

Do not open the high pressure fuel system with the
engine running. Engine operation causes high fuel
pressure. High pressure fuel spray can cause serious
injury or death.

4

STARTING AND OPERATING

263

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands