manualshive.com logo in svg

Dodge 2015 RAM, Owner'S Manual

Share
Download
Dodge 2015 RAM Owner'S Manual Download Page 227

2. The engine RPM will go up to 1100 RPM. To increase

the RPM, press and hold the ACCEL/RESUME switch
and the idle speed will increase to approximately 1500
RPM. To decrease the RPM, press and hold the DECEL
switch and the idle speed will decrease to approxi-
mately 1100 RPM.

3. To cancel the Idle–Up feature, either press the CAN-

CEL switch, press the ON/OFF switch, or press the
brake pedal.

Stopping The Engine

Idle the engine a few minutes before routine shutdown.
After full load operation, idle the engine three to five
minutes before shutting it down. This idle period will
allow the lubricating oil and coolant to carry excess heat
away from the combustion chamber, bearings, internal
components, and turbocharger. This is especially impor-
tant for turbocharged, charge air-cooled engines.

NOTE:

•

During engine shut down on vehicles equipped with
manual transmissions, it is normal for the diesel en-
gine to resonate heavily for a moment during engine
shut off. When the engine is connected to a manual
transmission, this resonance causes load gear rattle
from the transmission. This is commonly referred to as
“shut down rattle.” The manufacturer recommends
performing engine shut down with the clutch pedal
pushed to the floor (clutch disengaged). When engine
shut down is performed in this manner the rattle is
reduced (not eliminated).

•

Refer to the following chart for proper engine shut-
down.

4

STARTING AND OPERATING

225

Summary of Contents for 2015 RAM















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands