Dobot Magician Lite User Manual Download

Page: 30 / 72

Dobot Magician Lite User Guide

Interface Description

Issue V1.9.1 (2020-01-11)

User Guide

Interface Description

Magician Lite Interface Description

The interfaces of Magician Lite are located on the back of the base. Figure 4.1 shows the

interfaces on the back of the base, and Table 4.1 lists the description.

Figure 4.1 Interfaces in the base

Table 4.1 Interface description

No.

Description

Power switch

Short press: Power on Magician Lite

Long press(>3s): Power off Magician Lite

Key



Short press: Start running playback program in offline mode, for the details

about offline mode, please refer to 5.4Working in Offline Mode



Long press(>2s): Start homing procedure, for the details about homing,

please refer to 5.2Homing

Power interface

Connect to power adaptor

12V power interface: To supply power to Magician Lite

USB: Connect Magician Lite and your PC

10PIN communication interface

Serial communication

The LED indicator is located on the base, Table 4.2 lists the status description.

Summary of Contents for Magician Lite









































































Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands

Dobot Magician Lite, User Manual

Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands