Dobot Magician Lite Page 32 User Manual Download

Page: 32 / 72

Dobot Magician Lite User Guide

Interface Description

Issue V1.9.1 (2020-01-11)

User Guide

Figure 4.3 Power Box interface description

Table 4.3 Power Box LED description

State

Description

Flashing

In discharge

Water lights

Charging

All on

Charging complete

Turn off after all flashing

Low battery, automatic shutdown

The inside and outside

lights flash alternately

The temperature of the Power Box is too high or too low. At this time, the Power

Box needs to be left for a period of time until the temperature is within the working

temperature range

Multiplexed I/O Interface Description

The addresses of the I/O interfaces in Magic Box are unified. Most of I/O interfaces have

multiple functions, to control the peripheral equipment.

Figure 4.4 shows the communication interface on Magic Box, Table 4.4 lists the multiplexed

I/O description.

Summary of Contents for Magician Lite









































































Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands

Dobot Magician Lite, User Manual

Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands