Dobot Magician Lite Page 39 User Manual Download

Page: 39 / 72

Dobot Magician Lite User Guide

Operation

Issue V1.9.1 (2020-01-11)

User Guide

Figure 5.2 The General Setting page

Table 5.2 The General Setting page



Items

Description

General

Set a device name and collision detection

Update

Set firmware detection frequency and view the current firmware, software
version

Firmware

Upgrade firmware

DobotStudio displays different firmware when connecting different devices.
When connecting Magician Lite, firmware shows

Magician Lite firmware

. You

can click

Confirm

to upgrade firmware.

Jog

Set the jogging speed ratio

Playback

Set speed ratio, Jump parameters, handhold teaching, and LostStepParam.

Write Draw

Set the Write & Draw function, such as speed ratio, pen up offset and pen down
position.

Common Areas of DobotStudio Page

The DobotStudio offers the following common areas shared by all the function modules to

control the robotic arm.



You can select the liner rail or an end-effector on the DobotStudio page, as shown in

Figure 5.3.

Summary of Contents for Magician Lite









































































Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands

Dobot Magician Lite, User Manual

Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands