Dixie Narco DN 2145 Technical Manual Download Page 31

Page: 31 / 89

These charts are intended as a guide to isolate and correct most problems you might encounter. Should your
machine scroll ‘OUT OF SERVICE”, go in the TEST MODE and press “B” to list errors.

ALL COINS ARE REJECTED

All coins are rejected.

Main Power OFF /

Disconnected.

Apply power

Blown Fuse

Check fuses and

replace if

necessary.

Loose connection.

Check cable at

coin mech and

controller board.

Jammed coin

mechanism.

Clear coins.

Weak springs on changer

gate. (COINCO units

only.)

Replace spring.

Gate partially open.

Clean and reset

gate. If

COINCO unit,

check spring.

Dirty / faulty coin sensor.

Clean / Replace.

Incompatible coin

mechanism.

Replace.

Defective coin

mechanism.

Replace.

Defective controller

board.

Replace.

Summary of Contents for DN 2145


























































































Search results

Summary of Contents for DN 2145

Reviews:

Related manuals for DN 2145

Brands by name

Popular brands

Dixie Narco DN 2145, Technical Manual

Search results

Summary of Contents for DN 2145

Reviews:

Related manuals for DN 2145

Brands by name

Popular brands