Dixie Narco DN 2145 Technical Manual Download

Page: 63 / 89

LIGHTING / EVAPORATOR FAN

ITEM

PART DESCRIPTION

Assembly, Ballast 120V/60Hz Electronic (Sylvania) T8 Electronic

(0304-8225 & up)

804,400,69x.x1

Assembly, Ballast 120V/60Hz Electronic (Advance) T8 Electronic

(0304-8225 & up)

804,400,68x.x1

Assembly, Ballast 120V/60Hz Electronic T8 Magnetic Rapid Start (prior to 0304-8225)

804,400,54x.x1

Assembly, Ballast 220-240V / 50 Hz Export HF-Basic II was 804,400,56x.x1

804,401,07x.x1

Lamp, Fluorescent T8 48” F32T8TL841 (0304-8225 & up)

804,700,65x.x1

Lamp, Fluorescent 40W 48” (prior to 0304-8225)

W845

Lens, Lamp Extrusion

801,904,15x.x1

Lens, Lamp Assembly – W351

RB 3A

Lens, Lamp Assembly – 801,903,91x.x1

RB 3A

Lamp Holder Assembly, T8 Electronic (includes base and harness) 110V

(0304-8225 & up)

622,062,50x.x3

Lamp Holder Assembly, T8 Magnetic 110V (prior to 0304-8225)

622,060,20x.x3

Lamp Holder Assembly (includes base and harness) 220-240V

622,061,50x.x3

Lamp Holder Bracket, T8 Electronic (0304-8225 & up)

622,020,22x.x3

Lamp Holder Bracket, T8 Magnetic (prior to 0304-8225)

Lighting Harness T8 Electronic (0304-8225 & up)

804,920,51x.x1

Lighting Harness T8 Magnetic (prior to 0304-8225)

804,913,78x.x1

Lighting Harness 220-240V

804,926,04x.x1

Evaporator Fan Assembly (120V/60Hz, 9W) Energy Star New EBM 5 Blade Metal

647,052,10x.x3

Evaporator Fan Assembly (120V/60Hz, 9W) Energy Star ECM Original 7 Blade Plastic

627,052,40x.x3

Evaporator Fan Assembly (120V/60Hz, 9W) Non Energy Star was W362

622,041,10x.x3

Evaporator Fan Assembly (230V/50Hz, 9W) was W287

622,041,00x.x3

Evaporator Fan Assembly (220V/50Hz, 9W)

622,043,00x.x3

**8

Evaporator Fan Motor, EBM 5 Blade Metal (120V/60Hz) Energy Star

804,501,48x.x1

Evaporator Fan Motor, 58mm ECM 7 Blade Plastic (120V/60Hz) Energy Star

804,501,28x.x1

Evaporator Fan Motor (115V/60Hz) Non Energy Star was W369

804,501,09x.x1

Evaporator Fan Motor (230V/50Hz, 9W)

W130

Evaporator Fan Motor (220-230V/50Hz)

804,501,11x.x1

Choke (Energy Star Evaporator Assy)

804,920,41x.x1

Harness, Energy Star Evaporator Choke Extension

804,922,77x.x1

Harness, Energy Star Evaporator

804,922,37x.x1

Rear Evaporator Mounting Bracket

635,050,14x.x3

Notched Evaporator Mounting Bracket

635,050,15x.x3

Evaporator Drain Pan Assembly

622,041,20x.x3

Door Stiffener Angle, Recovery Flap

622,070,05x.x3

Vertical Edge Cover Strip

803,865,86x.x1

Top Edge Cover Strip

803,866,37x.x1

Evaporator Duct Air Deflector

W448

Part numbers & descriptions are subject to change with out notice.

NA = Not applicable

TBD = To be determined RB = Replaced by

** Important: An EBM Fan will not fit in the ECM Fan Housing Assembly.
* The Evaporator Fan Assemblies are interchangeable in the vender.

Summary of Contents for DN 2145


























































































Search results

Summary of Contents for DN 2145

Reviews:

Related manuals for DN 2145

Brands by name

Popular brands

Dixie Narco DN 2145, Technical Manual

Search results

Summary of Contents for DN 2145

Reviews:

Related manuals for DN 2145

Brands by name

Popular brands