manualshive.com logo in svg

Dixie Narco DN 2145, Technical Manual

The Dixie Narco DN 2145 is a reliable and efficient vending machine that can offer a wide variety of beverages and snacks. To ensure smooth operation and maintenance, make sure to download the free Technical Manual from manualshive.com. This comprehensive manual provides step-by-step instructions, troubleshooting tips, and essential information to maximize the machine's performance.

Share
Download
background image

 

  2 

Table of Contents 

 

GENERAL INFORMATION ..................................................................................................... 4 

Vender Safety Precautions .......................................................................................... 4 
Product Identification .................................................................................................. 4 
Physical Characteristics .............................................................................................. 4 

INSTALLATION & SETUP ................................................................................................. 4 - 9 

Receiving Inspection ................................................................................................... 4 
Unpacking The Vender................................................................................................ 5 
Electrical Requirements .............................................................................................. 5 
Ground The Vender .................................................................................................... 5 
Installation & Setup Instructions .............................................................................. 5 - 6 
Placing the Vender On Location................................................................................... 6 
Leveling the Vender.................................................................................................... 6 
Spacing the Vender ............................................................................................... 6 - 7 
Installing Labels & Flavor Cards................................................................................... 7 
Coin  Changers And Other Accessories ........................................................................ 7 
Set Temperature Control ........................................................................................ 7 - 8 
Loading the Vender..................................................................................................... 8 
Loading the Coin Changer........................................................................................... 8 
Power Distribution Box ................................................................................................ 8 
Vending Machine Controller (VMC).............................................................................. 8 
Keypad ...................................................................................................................... 8 
Digital Display ............................................................................................................ 8 
Refrigeration System ............................................................................................. 8 - 9 
Shelf Assembly........................................................................................................... 9 
Shelf Stabilizer ........................................................................................................... 9 
Gate Assembly ........................................................................................................... 9 
Slide / Pusher Assembly ............................................................................................. 9 
 

PROGRAMMING........................................................................................................... 10 - 23 

General .................................................................................................................... 10 
External Display Items .............................................................................................. 10 
Normal Operation Messages ..................................................................................... 10 
Initial Programming............................................................................................ 11 - 12 
Quick Reference Menu Items .................................................................................... 13 
Service Mode ....................................................................................................14 – 16 
Test Mode .........................................................................................................16 – 19 
Setup Mode.......................................................................................................19 – 21 
Setup Mode 2.................................................................................................... 21 - 23 

GENERAL MAINTENANCE ........................................................................................... 24 - 25 

Power ...................................................................................................................... 24 
Cleaning .................................................................................................................. 24 
Eprom Replacement ................................................................................................. 25 

MAJOR COMPONENT DESCRIPTION .......................................................................... 26 - 27 

AC Distribution Box / Refrigeration DN55##/54##/2145............................................... 26 
AC Distribution Box / Refrigeration Unit DN35## ......................................................... 27 

ELECTRICAL DIAGRAMS & SCHEMATICS .................................................................. 28 - 29 

MDB Controller Connections ..................................................................................... 28 
Dual Sensor Board ................................................................................................... 29 

TROUBLESHOOTING...................................................................................................30 – 39 

Coin Acceptance ...................................................................................................... 30 
Bill Acceptors ........................................................................................................... 30 
Control Board ........................................................................................................... 30 
All Coins Rejected .................................................................................................... 31 
All Bills Rejected....................................................................................................... 32 
Incorrect Change Dispensed ..................................................................................... 33 
Selection Will Not Vend ............................................................................................. 34 
Ice / Frost on Evaporator........................................................................................... 35 
Condensate on Outside of Product Door .................................................................... 35 
Compressor Will Not Stop ......................................................................................... 35 

Summary of Contents for DN 2145


























































































Reviews:

No comments

Related manuals for DN 2145

Panasonic KX-TG234SK Service Manual preview
KX-TG234SK
Brand: Panasonic Pages: 99
Bay Tek Games GUITAR EDITION JAM SESSION Service Manual preview
GUITAR EDITION JAM SESSION
Brand: Bay Tek Games Pages: 35
Quasar Autopax PAX405 User Manual preview
Autopax PAX405
Brand: Quasar Pages: 124
Singer Stylist 533 Manual preview
Stylist 533
Brand: Singer Pages: 68
Singer 79-1 Parts List preview
79-1
Brand: Singer Pages: 30
Sega Ghost Squad Owner'S Manual preview
Ghost Squad
Brand: Sega Pages: 92
UNIS DYNAMIC ORBS Operation Manual preview
DYNAMIC ORBS
Brand: UNIS Pages: 28
JUKI DU-141H-4 Instruction Manual preview
DU-141H-4
Brand: JUKI Pages: 44
Sharp FO-P610 Specifications preview
FO-P610
Brand: Sharp Pages: 2
Sharp FO-IS110N Quick Setup Manual preview
FO-IS110N
Brand: Sharp Pages: 2
Sharp FO-K01 Operation Manual preview
FO-K01
Brand: Sharp Pages: 26
Sharp UX-144 Operation Manual preview
UX-144
Brand: Sharp Pages: 52
Sharp UX-460 Service Manual preview
UX-460
Brand: Sharp Pages: 69
Sharp UX-A255 Operation Manual preview
UX-A255
Brand: Sharp Pages: 112
Sharp MX-FX11 Service Manual preview
MX-FX11
Brand: Sharp Pages: 57
Sharp UX-600M Operation Manual preview
UX-600M
Brand: Sharp Pages: 118
Sharp UX-60 Operation Manual preview
UX-60
Brand: Sharp Pages: 118
Sharp UX-40 Service Manual preview
UX-40
Brand: Sharp Pages: 102

Brands by name

Popular brands

Load more brands