– 981 –
41
Q
UALITY
OF
S
ERVICE
C
OMMANDS
The commands described in this section are used to configure
Differentiated Services (DiffServ) classification criteria and service policies.
You can classify traffic based on access lists, IP Precedence or DSCP
values, or VLANs. Using access lists allows you select traffic based on Layer
2, Layer 3, or Layer 4 information contained in each packet.
Table 122: Quality of Service Commands
Command
Function
Mode
Creates a class map for a type of traffic
GC
Specifies the description of a class map
CM
Defines the criteria used to classify traffic
CM
Redefines the name of a class map
CM
Creates a policy map for multiple interfaces
GC
Specifies the description of a policy map
PM
Defines a traffic classification for the policy to act on
PM
Redefines the name of a policy map
PM
Defines an enforcer for classified traffic based on a
metered flow rate
PM-C
Defines an enforcer for classified traffic based on a
single rate three color meter
PM-C
Defines an enforcer for classified traffic based on a two
rate three color meter
PM-C
Classifies IP traffic by setting a CoS, DSCP, or IP-
precedence value in a packet
PM-C
Applies a policy map defined by the
command to the input of a particular interface
IC
Displays the QoS class maps which define matching
criteria used for classifying traffic
PE
Displays the QoS policy maps which define
classification criteria for incoming traffic, and may
include policers for bandwidth limitations
PE
Displays the configuration of all classes configured for
all service policies on the specified interface
PE
Summary of Contents for DG-GS4826S
